Waterbed Heaters
1-800-883-8828
How to use the Thermal Guardian Ener-Save Safe Heater
Safely!
Waterbed heaters for both traditional hardside and
softside beds have been improved recently with safety and comfort
advances. These advances affect some of the installation and use
conditions of theh eaters and must be addressed before your new heater is
installed. The new motionless water mattresses have also contributed to
the heater advances. These new mattress designs have increased fiber
filling in the mattress interior to the degree that the water is virtually
trapped and almost no water circulation occurs. One of the safety advances
is lowering the operating temperature of the heater pad when it is
working. The addition of a sensitive fuse in the pad is another safety
improvement keeping the pad from ever reaching too hot of a temperature.
The next section will provide you with some important tips on the proper
heater installation to give you the maximum enjoyment of your sleep
environment.
The next section will provide you with some important tips on the proper
heater installation to give you the maximum enjoyment of your sleep
environment.
Never plug in the heating unit until the mattress
is completely filled with water. The Thermal Guardian® Temperature
Control Systems are designed with your safety as our number one concern.
Each heating pad is engineered to shut down in the event of an overheating
situation. Under normal use, this is an outstanding feature; however, if
the pad is heated without the proper depth of fluid to whisk the heat
away, the safety fuse can trip which renders the pad unable to operate.
Some models of the Thermal Guardian® heating pads are rolled at the
factory. The proper method of flattening the pad is done by using the
reverse roll. Do not heat the pad, as this may cause the safety fuse to
trip. To ensure proper enjoyment of your new flotation sleep system,
always fill the mattress with warm water. This can be done using a faucet
adaptor attached to any kitchen or bathroom sink. The use of a cold water
fill will prolong the warm up time. The Ener-Save design allows the pad to
raise the temperature of the water at the approximate rate of _ to _
degree Fahrenheit per hour. Assuming a cold tap temperature of 45 degrees,
this will bring the bed to a comfortable sleeping temperature in 5-7 days.
To avoid this delay, the warm water fill can provide you a great night’s
sleep on the very first night. If your hot water tank is drained during
the fill process, simply turn off the water supply and wait approximately
30-45 minutes. The mattress should be filled to within approximately 1”
below level with the frame. It is always easier to add a few pitchers of
water to create a less-supportive feel, than it is to drain an overfilled
mattress. Once the mattress is filled, it is recommended that no
adjustment be made for 7-10 days to allow the body to adjust to the new
support system.
Proper
placement of the heater during installation is critical to the long life
and enjoyment of your Thermal Guardian® Temperature Control system. The
heater pad must be positioned upon a rigid surface without any foreign
material, such as blankets or sheet, coming in contact with the pad. Never
place the pad over any crack sor imperfections in the foundation or
decking. The pad must be directly underneath the safety liner. The black
temperature sensor should be a minimum of 12” from the pad and 6” from the
sides of the bed to provide accurate temperature readings. The mattress is
then placed on the liner, inside of the frame perimeter.
Open the fill valve on the mattress and inflate it
with air until it is about 2 feet tall.Replace the cap and pushdown on the
center of the expanded mattress to force the wrinkles from the bottom of
the mattress which will help prevent issues with the heater pad. This also
allows you to center the mattress easily in the frame as you release the
air from the mattress and prepare for a warm water fill. By centering the
mattress with air you will ensure a comfortable fit and a great night’s
rest for years to come.
Periodic conditioning of the inside and outside of
your vinyl water mattress will improve your overallenjoyment and provide a
more comfortable night’s sleep.Upon finishing the initial fill of your
mattress, place8 ounces of a Fiber Bed waterbed conditioner inside the
chamber (for Dual chambers add 4 ounces to each side).This will adequately
treat the water (for well water it is recommended to double this dosage)
for one year. Theconditioner prevents algae growth in the water, which in
turn minimizes air bubbles. It also lubricates the inside ofthe vinyl to
keep it soft and supple. To create the same level of protection on the
outside of the mattress, the useof a Waterbed Vinyl Conditioning spray
will remove body oils which if left unattended, can cause the vinyl
tobecome brittle. Cleaning the surface bi-monthly will help prolong the
life of the mattress and enhance the comfort.
Plug in your heater and enjoy your warm waterbed!
